FSP MP5 and NP7 Air Coolers Review: Simple and effective | Tom's Hardware

FSP’s MP5 is an excellent entry-level cooler with low noise levels and a reasonable price.

Reasonable pricing

Can be installed without removing the fans

Good thermal performance

Full RAM Clearance

NP7 might be difficult to install (see installation section)

Why you can trust Tom's HardwareOur expert reviewers spend hours testing and comparing products and services so you can choose the best for you. Find out more about how we test.

Most of my recent reviews have focused on high end AIOs for users who are looking for the best cooling available for their computers, but the simple fact is that most folks would be well served by a basic single- or dual-tower air cooler. Today we’re going back to basics and examining two air coolers by FSP, a company better known for power supplies like the Vita GM 850W, although we’ve also covered the FSP CMT520 Mid-Tower ATX RGB Case.

Will FSP’s MP5 and NP7 make our list of the best coolers on the market? Let’s take a look at the specifications and features of these products, then we’ll go over thermal performance and noise levels to see where they stand.

Cooler

FSP MP7

FSP NP5

MSRP

$47.99 USD

$27.99 USD

Radiator Material

Aluminum

Aluminum

Lighting

None (ARGB Version is available)

None (ARGB Version is available)

Warranty

3 Years

3 Years

Socket Compatibility

Intel Socket LGA 1851/1700/1200 AMD AM5 / AM4

Intel Socket LGA 1851/1700/1200 AMD AM5 / AM4

Unit Dimensions (including fans)

125 (L) x 123.5 (W) x 153mm (D)

120 (L) x 94 (W) x 151 mm (D)

Base

Copper cold plate

Direct-Touch Heatpipes

Maximum TDP (Our Testing)

>247W with Core i7-14700K >283W with Core Ultra 9 285k

>229W with Core i7-14700K >260W with Core Ultra 9 285K

The packaging for the FSP air coolers is efficient, with no excess. The contents are protected primarily by molded foam, but the accessories are packaged inside plastic bags.

Included in the box are the following:

▶️ Thermal Paste Tube

FSP’s air coolers arrive with a thermal paste tube that’s large enough for multiple installations.

▶️ Direct touch copper heatpipes

The entry level NP5 cooler has four direct-touch copper heatpipes for the most efficient heat dissipation. The MP7 includes six standard heatpipes, as it is very difficult to create coolers with more than six heatpipes and make them direct-touch.

▶️ Basic tower radiators

The design of the radiators on the NP5 and MP7 are essentially the same, with a basic no-frills look.

The covers of each heatsink tower are embossed with FSP’s logo.

▶️ Full RAM compatibility

A problem posed by some air coolers is incompatibility with tall RAM. But with FSP’s NP5, there are zero RAM compatibility issues at all!

This is mostly the same for the more powerful MP7 model. You won’t have any compatibility issues if you are using RAM slots two and four. However, you might have issues with the tallest RAM DIMMs if you’re populating all four slots.

▶️ 120mm fans

There’s more to a cooler than just the heatsink or radiator. The bundled fans have a significant impact on cooling and noise levels, as well as how the cooler looks in your case. The fans included are simple and standard, with an all-black aesthetic and an etched metal disc covering the hub with FSP’s logo.

Dimensions

120 x 120 x 25mm

Fan Speed

800-1800 RPM ± 10%

Air Flow

Up to 76 CFM

Air Pressure

Up to 2.1 mmH2O

Bearing Type

FDB

MTTF

Unlisted

Lighting

None

CPU

Intel Core i7-14700K

GPU

ASRock Steel Legend Radeon 7900 GRE

Motherboard

MSI Z790 Project Zero

Case

MSI Pano 100L PZ Black

System Fans

Iceberg Thermal IceGale Silent

There are many factors other than the CPU cooler that can influence your cooling performance in your system, including the case you use and the fans installed in it. A system's motherboard can also influence this, especially if it suffers from bending, which results in poor cooler contact with the CPU.

In order to prevent bending from impacting our cooling results, we’ve installed Thermalright’s LGA 1700 contact frame into our testing rig. If your motherboard is affected by bending, your thermal results will be worse than those shown below. Not all motherboards are affected equally by this issue. I tested Raptor Lake CPUs in two motherboards. And while one of them showed significant thermal improvements after installing Thermalright’s LGA1700 contact frame, the other motherboard showed no difference in temperatures whatsoever! Check out our review of the contact frame for more information.

I’ve also tested this cooler with Intel’s latest platform, Arrow Lake and LGA 1851.

CPU

Intel Core Ultra 9 285K

GPU

MSI Ventus 3X RTX 4070Ti Super

Motherboard

MSI Z890 Carbon Wifi

Case

MSI MPG Gungnir 300R

System fans

Pre-installed case fans

The installation of both coolers is relatively simple. The entry-level NP5 is especially easy to install.

1. You’ll first need to place the backplate against the rear of the motherboard, (optionally) using the adhesive strips to secure it.

2. Next, you’ll need to take the mounting studs ( which include plastic spacers) and push them against the backplate’s screw holes. Once complete, they will be secure, which makes installation easier if you choose not to use the adhesive strips.

3. Next, take the mounting plate and orient it as appropriate, then secure it with the included screws. The NP5 installation is shown below, but you’ll want to rotate the plate for the MP7’s installation.

4. Apply the included thermal paste to your CPU. If you have any questions on how to do this properly, please refer to our handy guide on how to apply thermal paste.

5. Place the CPU heatsink on top of the mounting plate and secure it with a screwdriver. This is easiest on the NP5 model, as both mounting screws are exposed and you can see where you’re aiming.

The installation of the NP7 may be slightly more difficult, depending on your motherboard and skill level. It can be difficult to tell where you’re aiming with the NP7’s installation, because the screws are located underneath the heatsink. But the included long screwdriver and screwdriver holes are there to guide you.

6. Once complete, connect the PWM cable to the CPU fan header and turn on your computer.

Current page:Features and Specifications

Albert Thomas is a contributor for Tom’s Hardware, primarily covering CPU cooling reviews.

Micron shows off world's fastest PCIe 6.0 SSD, hitting 27 GB/s speeds — Astera Labs PCIe 6.0 switch enables impressive sequential reads

Cooler Master MWE Gold 850 V3 power supply review

How to fix Salmon Skin Problems in 3D Prints